How to Turn on a Boiler: 7 Steps Guide

介绍

It’s not difficult to turn on a boiler, but there are some safety precautions you need to know. This guide will walk you through the process of turning on your boiler and making sure that everything is safe for use.

步 1: Check the power switch.

The first thing you’ll want to do is check the power switch. If it’s off, turn it on. If it’s already on and you still don’t have hot water, then there may be a problem with your boiler itself or its controls.

If your boiler has an electronic control board (ECB), flip through its menu until you find an option called “力量” or “switch“. And see if that works, or if there isn’t one at all. If there are several different settings for “on/off,” try switching between them to see if any make a difference in how quickly your hot water comes out of the faucet.

步 2: Turn the gas supply on and open the cover.

Secondly. To turn the gas supply on, you will need to go to your boiler and press a button. The button is usually located near where you would normally open the cover of your boiler.

When you have pressed this button, there should be some sort of indicator light or sound that lets you know that it has been turned on successfully. If this doesn’t happen straight away, try pressing again until you get an indication from your boiler that it has been turned on successfully.

步 3: Once you have turned all your devices on, check for leaks.

Third. Once you have turned all your devices on, check for leaks. Check for gas leaks by smelling the air around your boiler. If it smells like gas, turn off the main switch and contact a professional plumber immediately.

检查房屋的地板或天花板是否漏水，看看是否有水从上面滴下来. 如果这些区域有任何湿气，请立即致电水管工，因为如果不尽快修复，可能会导致进一步的损坏!

您还可以在每个散热器下方放置一个空玻璃来检查地板下方，以查看首次启动时是否有蒸汽冒出 (或经过一段时间后).

步 4: 检查压力表.

第四. You should also check the pressure gauge to ensure it is not reading too high. If this reading is too high (more than 150 psi) then it means that there is too much steam inside of it. Turn off your boiler immediately and call a plumber.

步 5: Check all fittings are tight and secure.

Fifth. Check all fittings are tight and secure.

1. Ensure that the water inlet valve is closed, as to prevent damage to the 泵.
2. Make sure the pump is working properly and there’s no air trapped in it, which would stop it from working efficiently or at all!
3. Check that the gas valve is open (this will be indicated by a red light). As this will allow gas to flow through into your boiler for it to ignite and heat up properly.
4. Check that your hot water cylinder isn’t blocked up with sediment or lime scale. This could lead to overheating or leakages from it if left unchecked long enough!
5. It’s important that the flue pipe is clear at all times to ensure that no dangerous fumes can escape from your boiler into your home.

步 6: Set the time and temperature to suit you.

Sixth. Set the time and temperature to suit you.

• How to set the time: Press [Time] until the current hour appears on the screen, then press [OK]. The next step is to enter minutes by pressing [Minute] 或者 [Max Min]. If you want to go back, use [Back]. Once done with setting up your day’s schedule, press [Save] to store it in memory or choose another option from the menu.
• How to set temperature: Press the “up” or “down” buttons during the heating operation until you reach desired temperature level (Fan Only mode). You can also set fan speed using the same method as above but by pressing the “high/low” button instead of the temperature button. (笔记: 如果按向上/向下按钮后没有反应 8 几秒钟然后等待系统识别输入后再继续)

步 7: 打开锅炉.

最后. 您可以通过按下按钮或转动旋钮来打开锅炉. 最简单的方法是按控制面板上的开始按钮. 如果您有老式手动锅炉, 然后你需要打开它的门并拉出一些杠杆来启动它.

结论

We hope this guide has helped you to understand the process of how to turn on a boiler. If there is anything else that we can help with, please contact us and we will do our best!

About Dabonn

Zhengzhou Dabonn Energy Co., 有限公司.

我们有超过 20 在锅炉系统设备研发和制造方面的多年经验. 并致力于设计和生产适合您需求的锅炉, including fire-tube, water-tube, 和蒸汽锅炉, while also staying up-to-date with the latest technological boiler.